Gasket Plate Heat Exchanger Type I60H Carbon Steel Material HS CODE 8419500090 Apply in Electric Power Industry
Introduction :
Gasket Plate Heat Exchanger is a heat transfer device that consists of a series of individual plates that can be easily disassembled and reassembled. Each plate has special patterns that create flow channels for the hot and cold fluids, allowing efficient heat exchange to occur. The detachable design offers flexibility for maintenance, cleaning, and modifications.
Application :
HVAC industry, Chemical industry, Power generation industry, Oil and gas industry, Metallurgical industry, Pulp and paper industry, Textile Industry, Paper making , Concentrated heating, Electric power industry, Oil prodution industry, Marine, etc .
Apply in Electric Power Industry :
- Cooling of Generator Shaft Pump
- Cooling of Transformer Oil
Proper care and maintenance of gasketed plate heat exchangers (GPHEs) are crucial to ensure their optimal performance and longevity. Here are some key care and maintenance practices for GPHEs:
Regular Cleaning: GPHEs should be cleaned periodically to remove any fouling or deposits that can reduce heat transfer efficiency. The frequency of cleaning depends on the application and the nature of the fluids being processed. Follow the manufacturer's guidelines for cleaning procedures and use appropriate cleaning solutions to avoid damaging the plates or gaskets.
Inspect and Replace Gaskets: Inspect the gaskets regularly for signs of wear, damage, or leakage. Gaskets should be replaced if they are worn out, cracked, or no longer provide a tight seal. Use genuine replacement gaskets recommended by the manufacturer to ensure proper fit and performance.
Check for Leaks: Routinely inspect the GPHE for any signs of leakage, such as fluid drips or stains. If a leak is detected, identify the source and take appropriate action to address it. Leaks can occur due to damaged gaskets, loose connections, or plate corrosion. Promptly repair or replace any faulty components to prevent further damage and maintain efficient operation.
Monitor and Control Fluid Parameters: Regularly monitor the temperature, pressure, and flow rates of the fluids passing through the GPHE. Ensure that the operating parameters are within the recommended limits specified by the manufacturer. Deviations from the recommended parameters can affect heat transfer efficiency and potentially damage the heat exchanger.
Prevent Scaling and Corrosion: Scaling and corrosion can reduce heat transfer efficiency and damage the plates. Implement appropriate water treatment measures, such as using water softeners or chemical inhibitors, to prevent scaling and corrosion. Follow the manufacturer's recommendations for water quality and treatment methods.
Inspect Plate Condition: Periodically inspect the condition of the plates for signs of corrosion, erosion, or deformation. If any plates are damaged or distorted, they should be replaced to maintain optimal heat transfer performance. Regular inspections can help identify potential issues early and prevent further damage.
Maintain Proper Flow and Pressure: Ensure that the GPHE is operated within the recommended flow and pressure ranges. Improper flow rates or excessive pressure can lead to reduced heat transfer efficiency, increased fouling, or damage to the plates. Install appropriate flow meters and pressure gauges to monitor and control the flow and pressure levels.
Follow Manufacturer's Guidelines: Always refer to the manufacturer's guidelines and recommendations for care, maintenance, and operating procedures specific to your GPHE model. The manufacturer's instructions will provide valuable information on cleaning methods, gasket replacement, inspection intervals, and other maintenance requirements.
| TYPE | A(mm) | B(mm) | C(mm) | D(mm) | E(mm) | Height ( mm ) ( from middle of bottom to ground (mm) | MAX.LC (mm) | Connector Path (mm) | Max Flow (m3/h) | Design Pressure (Mpa) | Max Pieces |
| I60B | N(2.0+X) | 320 | 140 | 920 | 689 | 115 | 1200 | 50 | 36 | 1.6 | 250 |
| I60H | N(3.0+X) | 320 | 140 | 920 | 689 | 115 | 1200 | 50 | 36 | 1.6 | 203 |
| I100B | N(2.55+X) | 470 | 225 | 1051 | 763 | 160 | 1600 | 100 | 140 | 1.0/1.6/2.5 | 278 |
| I100H | N(3.95+X) | 470 | 225 | 1051 | 763 | 160 | 1600 | 100 | 140 | .0/1.6/2.5 | 180 |
| I130H | N(3.95+X) | 610 | 298 | 1591.4 | 1095.4 | 241 | 3000 | 150 | 360 | 1.0/1.6 | 600 |
| I150B | N(2.5+X) | 610 | 298 | 1790 | 1294 | 250 | 3000 | 150 | 360 | .0/1.6/2.5 | 600 |
| I150H | N(3.95+X) | 610 | 298 | 1790 | 1294 | 250 | 3000 | 150 | 360 | 1.0/1.6/2.5 | 600 |
Workshop :
Package :
Test Area :
Product Tags:
|
|
1.6Mpa Industrial Plate Water To Water Heat Exchanger Apply In Electric Power Industry Images
|
